$18.39 - $35.99
Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park Tool's 106-AC easily adapts the #106 Work Tray or PTH-1 Paper Towel Holder to fit 35mm-37mm upright tubes on PCS-9 Repair Stands, as well as 2003 and newer PCS-1, PCS-4, PCS-4-1, PCS-4-2 Repair Stands.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
Park's Work Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools and small parts close at hand. It has deep sides so your small items stay put and many slots for holding your tools. The Tool Tray fits Park's PRS-2, PRS-3, PRS-6, PRS-11, PRS-12, PCS-1 and PCS-4 repair stands.
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Team Race Stand. It makes travel easy and convenient, while also protecting your stand.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
The PCS-EXT is an extension for the older pre-2001 repair stands. The kit includes a quick-release collar and extension tube to raise the working height of the stand. The PCS-EXT is required for use of the 106-AC (sold separately).
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Includes a new tray/motor shroud, USB ports and oversized buttons to upgrade a Park Tool PRS-33 or PRS-33 AOK into the PRS-33.2 version controls and electronics.
A versatile and convenient way to keep tools, supplies and technology at arms length on a PRS-33 Power Lift Repair Stand. The PRS-33TT solidly mounts directly to either side of the stand’s upright at any height. - 19 tool holding holes, slots and small trays in a variety of shapes and sizes - 14-inch (35cm) magnetic tool bar - Integrated mounting holes for PTH-1 Paper Towel Holder - Phone/tablet/clipboard holder - Pen and pencil holders - Adjustable utility hook to hang wheels, parts and scales - Height adjustable - Can be installed on a fully assembled stand
Mount the THS-1 Trailhead Workstation (sold separately) directly to this rigid steel post. Features: - 2-inch (5cm) square post plated then powder coated for long outdoor life - Includes THS-1 mounting fasteners - 6-inch (15cm) square base with holes to mount directly into hard surface or to Park Tool #130 Base Plate (fasteners not included) - Height: 62.25-inch (158cm) positioning cradle arms at 50.5-inch (128cm)
Park Tool's 130 Repair Stand Base is designed for the PRS-3, PRS-3OSLB, PRS-3 OS-1, PRS-3 OS-2 and the PRS-23 LB Repair Stands (each sold separately). • 22-1/2" x 22-1/2" x 7/16" (57cm x 57cm by 1.1cm) steel plate • Approximately 68 lbs (31k) • Black painted
Built to withstand the rigors of every day shop use, Park' updated Single Arm Professional Work Stand is the stand of choice for professional mechanics around the world. • Easily height adjustable from 50" to 62" (128-158cm) utilizing Park's proven Lock Block System • Includes #105 cast aluminum work tray • Shop quality 100-3C Clamp quickly adjusts to fit any frame tube up to 1-5/8" (41mm) Notes: • The maximum weight holding capacity of the PRS-3.2 is 68 kg (150 lb.) • Stand does not include base. Order part #130 base • To mount directly to floor use part #FP-2 Floor Mounting Plate Differences from the PRS-3OS: • Utilizes lock block system which allows easy and fast height adjustment and a more solid connection between the two upright tubes • Also includes a new height adjustment pin which locks into place for safety and so it won't be lost
Page 1 of 1